Official Bank
0/547
Page
1/4
Implementing and Operating Cisco Service Provider Network Core Technologies (350-501 SPCOR) Exam (350-501) - Cisco Exam Questions
Last updated on June 20, 2026
97%
Exam Compliance
547
Total Questions
1
Question
Refer to the exihibit.
Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service-provider core network with these requirements: RC must establish LDP peering with the loopback IP address as its Router ID RA must establish LDP peering with RB. RC, and RY. How must the team update the network configuration to successfully enable LDP peering between RA and RC?
Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service-provider core network with these requirements: RC must establish LDP peering with the loopback IP address as its Router ID RA must establish LDP peering with RB. RC, and RY. How must the team update the network configuration to successfully enable LDP peering between RA and RC?
Options
A
Configure the mpls Idp router-Id loopback0 command on RA and RC.
B
Implement LDP session protection on RA.
C
Enable the mpls ip command on RC interface Gi2/0. DUMPS http://www.justcerts.com Questions & Answers PDF P-408
D
DUMPS Reset the discover hello hold time and interval to their default values.
Discussion
(0 comments)
to join the discussion
Community Discussion
No discussions yet. Be the first to ask!
Delete Comment
Are you sure? This action cannot be undone.
2
Question
Which type of attack is a Protocol attack?
Options
A
TFTP flood http://www.justcerts.com Questions & Answers PDF P-169
B
SYN flood
C
HTTP flood
D
Slowlorls
Discussion
(0 comments)
to join the discussion
Community Discussion
No discussions yet. Be the first to ask!
Delete Comment
Are you sure? This action cannot be undone.
3
Question
Refer to the exihibit. http://www.justcerts.com Questions & Answers PDF P-345
Refer to the exhibit. A network engineer is implementing multicast services on CPE-1 and CPE-2. CPE-1 must be configured as the preferred IGMP querier for the LAN segment. PIM-SM must be implemented on the LAN interfaces with an IGMP version that supports (*,
G) joins only. Which configurations must the engineer implement on CPE-1 and CPE-2?
A.
On CPE-1: interface GigabitEthernet0/1 ip address 10.0.12.129 255.255.255.128 ip pim sparse-mode ip igmp version 2 http://www.justcerts.com Questions & Answers PDF P-346
On CPE-2: interface GigabitEthernet0/1 ip address 10.0.12.130 255.255.255.128 ip pim sparse-mode ip igmp version 2 B.
On CPE-1: interface GigabitEthernet0/1 ip address 10.0.12.130 255.255.255.128 ip pim sparse-mode ip igmp version 3
On CPE-2: interface GigabitEthernet0/1 ip address 10.0.12.129 255.255.255. 128 ip pim sparse-mode ip igmp version 3
On CPE-1: interface GigabitEthernet0/1 C. ip address 10.0.12.130 255.255.255.128 ip pim sparse-mode ip igmp version 2
On CPE-2: http://www.justcerts.com Questions & Answers PDF P-347 interface GigabitEthernet0/1 interface GigabitEthernet0/1 ip address 10.0.12.129 255.255.255.128 ip address 10.0.12.129 255.255.255.128 ip pim sparse-mode ip pim sparse-mode D. ip igmp version 2
On CPE-1: interface GigabitEthernet0/1 ip pim sparse-mode ip igmp version 3 ip igmp version 3
On CPE-2: ip address 10.0.12.130 255.255.255.128
Refer to the exhibit. A network engineer is implementing multicast services on CPE-1 and CPE-2. CPE-1 must be configured as the preferred IGMP querier for the LAN segment. PIM-SM must be implemented on the LAN interfaces with an IGMP version that supports (*,
G) joins only. Which configurations must the engineer implement on CPE-1 and CPE-2?
A.
On CPE-1: interface GigabitEthernet0/1 ip address 10.0.12.129 255.255.255.128 ip pim sparse-mode ip igmp version 2 http://www.justcerts.com Questions & Answers PDF P-346
On CPE-2: interface GigabitEthernet0/1 ip address 10.0.12.130 255.255.255.128 ip pim sparse-mode ip igmp version 2 B.
On CPE-1: interface GigabitEthernet0/1 ip address 10.0.12.130 255.255.255.128 ip pim sparse-mode ip igmp version 3
On CPE-2: interface GigabitEthernet0/1 ip address 10.0.12.129 255.255.255. 128 ip pim sparse-mode ip igmp version 3
On CPE-1: interface GigabitEthernet0/1 C. ip address 10.0.12.130 255.255.255.128 ip pim sparse-mode ip igmp version 2
On CPE-2: http://www.justcerts.com Questions & Answers PDF P-347 interface GigabitEthernet0/1 interface GigabitEthernet0/1 ip address 10.0.12.129 255.255.255.128 ip address 10.0.12.129 255.255.255.128 ip pim sparse-mode ip pim sparse-mode D. ip igmp version 2
On CPE-1: interface GigabitEthernet0/1 ip pim sparse-mode ip igmp version 3 ip igmp version 3
On CPE-2: ip address 10.0.12.130 255.255.255.128
Reveal Only
Discussion
(0 comments)
to join the discussion
Community Discussion
No discussions yet. Be the first to ask!
Delete Comment
Are you sure? This action cannot be undone.
4
Refer to the exihibit. Refer to the exhibit. An engineer must Implement a traceroute operation to verity the R1 point-to-multipoint LSP connections. The traceroute operation must return all labels and hop-by-hop IP addresses for destinations 10.20.0.1. 10.30.0.1, and 10.40.0.1. and the maximum number of hops is 4. Which command must be executed to meet the http://www.justcerts.com Questions & Answers PDF P-416 requirements?
Question
Refer to the exihibit. Refer to the exhibit. An engineer must Implement a traceroute operation to verity the R1 point-to-multipoint LSP connections. The traceroute operation must return all labels and hop-by-hop IP addresses for destinations 10.20.0.1. 10.30.0.1, and 10.40.0.1. and the maximum number of hops is 4. Which command must be executed to meet the http://www.justcerts.com Questions & Answers PDF P-416 requirements?
Options
A
traceroute mpls traffic-eng tunnel-mte 10 responder-id 10.40.0.1
B
traceroute mpls ipv4 10.30.0.1/32 fee-type generic
C
traceroute mpls traffic-eng tunnel-mte 10 ttl 4
D
traceroute mpls ipv4 10.20.0.1/32 ttl 4
Discussion
(0 comments)
to join the discussion
Community Discussion
No discussions yet. Be the first to ask!
Delete Comment
Are you sure? This action cannot be undone.
5
Question
Refer to the exihibit.
Refer to the exhibit. An engineer started to configure a router for OSPF. Which configuration must the engineer perform on the router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?
Refer to the exhibit. An engineer started to configure a router for OSPF. Which configuration must the engineer perform on the router without changing any interface configuration so that the router establishes an OSPF neighbor relationship with its peer?
Options
A
router(config)# interface ethernet 1/1router(config-if)# no shutdown http://www.justcerts.com Questions & Answers PDF P-263
B
router(config)# interface ethernet 1/1router(config-if)# ip ospf hello-interval
C
router(config)# router ospf 11router(config-if)# no passive-interface ethernet 1/1
D
router(config)# interface ethernet 1/1router(config-if)# ip ospf priority 0
Discussion
(0 comments)
to join the discussion
Community Discussion
No discussions yet. Be the first to ask!
Delete Comment
Are you sure? This action cannot be undone.
Finish Practice?
Are you sure you want to finish? This will end your practice session.